IIX STANDOFF BRACKETS

SO-1 UNIVERSAL STANDOFF Our original single arm bracket, 39 inches long with a 1 1/8" o.d. pipe that is 5 1/2 inches long at the antenna end that will support the Ringo Ranger, 1/4 wave verticals, TV and scanner antennas as well as supporting a PO-1 pulley underneath to raise your low band wire antennas from the ground. Hot dipped galvanized steel construction, this bracket comes standard with 2 stainless hose clamps for mounting, but more may be used if necessary. This support is not recommended for the large 2 meter antennas, our heavy duty SO-2 will do the job. The bracket mounts on most tubular tower legs and ships U.P.S.
SO-1-S STANDOFF BRACKET Same as SO-1 but mounts on a flat surface with 2 fasteners. PO-1 pully kit attached to SO-1 standoff

PO-1 PULLY KIT Attaches to standoffs with a quick snap clip and has a lifetime lubed bushing to keep those wires hanging high.

SO-2 HEAVY DUTY UNIVERSAL STANDOFF This bracket picks up where the SO-1 leaves off. It will support all the "gain" two meter vertical antennas as well as various low band and business band antennas that can mount with 1 1/2 inch clamps. The arms will adjust to any tower width and 4 stainless clamps attach it to the tower legs. The bracket is constructed of 1 inch angle iron hot dipped galvanized and is 39 inches long. The 1 1/2 inch u bolts are spaced 10 inches apart to mount verticals or mast pipe

SO-3 COMMERCIAL HEAVY DUTY STANDOFF Available in 25"and 40" lengths.
This heavy duty bracket can be used on tower legs to 4 inches in diameter and the diagonals can be removed to accommodate various antennas and masts. Construction is 1 1/2 angle iron with heavy iron straps and bolts to attach to the tower. The bracket will accommodate 2 or 2 1/2 inch o.d. masts or antennas with the supplied u bolts. Special sizes are available on u bolts and all parts of these brackets are hot dipped galvanized. So-3 25" model weighs 34 lbs and the so3L 40" model weighs 47lbs. and all ship via U.P.S.

SO-4 ADJUSTABLE ANGLE STANDOFF
This 40 inch long angle iron bracket mounts an antenna vertically while adjusting to tower legs that are tapered as many styles of commercial towers are made. Two 1 1/2 inch u bolts secure the antenna while heavy straps bolt around the tower leg. It will work on tower legs tapering up to 30 degrees. Also will work on HDBX towers with a BX adapter.

SO-5 FIXED ANTENNA MOUNT

This mount fits on Rohn 25,45 and 55g towers and mounts a 2 " o.d. mastpipe to hold an antenna or dish on the side of the tower fixed on a desired direction. The mount includes two 1 1/2" hot dipped galvanized angles, four 1 1/2" ubolts and two 2" ubolts. Available in various lengths from the tower face, 6, 26 and 39 inches.

SO12 &SO13 MULTIPLE ANTENNA STANDOFFS These two standoffs will mount either two or three large vertical antennas and will mount directly on Rohn 25,45 or 55 towers. Other tower types can be accommodated by drilling additional holes for the hold down straps. Construction is heavy 1 1/2 angle iron hot dipped galvanized with necessary hardware included. Typical tower to antenna distance is 40 inches on a ROHN 25g tower.

MS4 MAST STANDOFF

This standoff clamps on a mast up to 3 inches and will mount 2 vertical antennas 6 feet apart. Hot dipped galvanized angle iron construction with all necessary hardware included. only one crossbar is shown here.

RM-16 ANTENNA / ROTOR MOUNT
Rotatable antenna sidemount for your tower. Mounts directly on all popular tower sections on one leg with 6 u bolts 1 1/2 inches in size. Antenna rotation is 300 degrees and the rotor shelf accepts higain / cde rotators. All parts are hot dipped galvanized and necessary hardware is supplied. As increased spacing distance between rotor and bearing shelves will allow large antennas to be mounted, the customer supplies the 2" o.d. pipe in the desired lengths